2N® NetStar

------------------------------------------
------ NetStar v3.0.x changelog ----------
------------------------------------------

****************** IMPORTANT!!! **********************
After upgrade to firmware 3.0.x from 2.x.x

- For sending voicemail to e-mail and for sending e-mails to user: You have to create a station type e-mail and setup FROM PORT outing
- Call forwarding is not possible to setup for stations - only for users
------------------------------------------------------

*** Firmware 3.0.15 ***
Improvements:
- maddr atribute processing for better interconnection with Microsoft OCS/Lync
- CO line electric current limitation improvement

Fixed problems:
- Autoclip routing didn´t work if there was settuped "Keep number type of Incoming CLIP" as "Replace unknown" on Virtual port
- Memory and performance optimalization. Under full load there were no messages played



*** Firmware 3.0.14 ***
Improvements:
- support of ISDN CONNECT_ACK

Fixed problems:
- wrong format of wav file when backup function was used in NS
- SNMP v3 support
- Customized message for voicemail could be played two times
- NS Admin wizard = changed default HW profile
- T38 FAX channel alocation (500 Invalid Media Parameters)
- Calee identification could be changed during routing through the ring table



*** Firmware 3.0.13 ***
Improvements:
- ASSISTANT - more possibilities to find the record
- Changes for CO line [default Impedance,overvoltage protection]
- Default: Busy Tone Israel
- DTMF det. profile


Fixed problems:
- DSP Issue, Can fix problems: recording, conference, memory. . .
- Progress is not deleted after recording new one
-


*** Firmware 3.0.12 ***
Improvements:
- memory monitoring, Assistant memory optimalization, more information in the “bug” packages

Fixed problems:
- Recording could stop if TAPI dialling is used
- Incorect tones fall down hierarchy and priority
- Record route in SIP - NS was not sending all parameters
- Audio in AUX port after more calls could stop
- UMTS module reset - if sms at no answer and a call was sended together



*** Firmware 3.0.11 ***
Improvements:
- Changes for Default IN/Default OUT parameters - tone settings



*** Firmware 3.0.10 ***
Improvements:
- sheduled UMTS restart / PBX restart
- PC Operator - support of dialed number in queue (you can see what number was dialled before entering the queue)

Fixed problems:
- ISDN modem changes. Different chip is used
- UMTS card boot fix. Unsupported baud rate.
- Add new timeout for answer in each transaction according RFC RFC-3261. Default value 200s.
- Call recording fix. (call was not recorded if T38 was switched ON)
- T38 – fix for tone detection. Problem if recording and t38 was enabled together.
- CO Line fix. (co line can be stuck if it is a part of bundle configuration)
- Cornet display history (Fix for dialed number after call transfer)



*** Firmware 3.0.9 ***
Improvements:
- New Jitter Buffer for SIP

Fixed problems:
- Fix for DNS server
- 9# support for ME mode
- CO Line FIX



*** Firmware 3.0.8 ***
Improvements:
- Trusted IP addresses on SIP trunks – to protect NS from hacker´s attacks
- Free minutes settings

Fixed problems:
- CO line problem, busy tone detection
- Fix for UMTS card. Boot problem.
- GSM not allowed logout
- NS restarts after changing profile



*** Firmware 3.0.7 ***
Improvements:
- Trusted IP addresses on SIP trunks – to protect NS from hacker´s attacks

Fixed problems:
- Call to alerting disa from bundle causes routing to next row
- Forwarding has influence on paramer "wait with queue". [RING TABLE]
- NS crashes when using the service "DTMF to CTI" after DISA
- Bad order of ringing extensions in Cyclic bundle
- The parsing of time stamp for call recording and incoming SMS in the Internal Assistant is not showing correctly



*** Firmware 3.0.6 ***
Fixed problems:
- Critical memory leak
- Missing AOC record if user has forwarding activated
- Reset when user changes profile
- Service Unavailable after Reinvite with T.38
- Calling party number - octet 3a
- Incoming hold clip for external numbers
- UMTS audio parameters settings
- fix for "hold clip" func.



*** Firmware 3.0.5 ***
- Missing AOC record if user has forwarding activated
- Service Unavailable after Reinvite with T.38



*** Firmware 3.0.4 ***
Improvements:
- Row copy to all colomns (in a router or Id tab)

Fixed problems:
- SIM card topping up by USSD
- T.38 support for CISCO (X-cap header)
- Labels printing issue in IE8
- Call transfer from ME extension on SIP issue



*** Firmware 3.0.3 ***
Improvements:
- SMS Call Back - max timeout [s,m,h] – you can specify exact time the system calls you back
- Assistant Server - Win 2008, Win 7 and Vista support (Apache 2.2)
- DSS1 synchronisation for NT ports
- P-Asserted-Identity option (important for CLIR calls over SIP)
- Cornet phone busy information in Event reporter
- Incoming hold clip for SIP phones
- Hang Up AT command pro Sierra Wirelless - AT+CHLD=0
- Extension number presentation during entering the conference room

Fixed problems:
- Complex Router default destination routing
- Presentation Restricted transmission in CLIP Router
- SMS at no answer not working if routed through DISA
- BRI Port didn't keep level 1 enable it's always down
- After changing user language from Assistant, properties aren´t set up
- “Prepare to print” button missing if the key modul s18 is connected to OpenStage T40



*** Firmware 3.0.2 ***
Improvements:
- Audio profile settings
- New progress for "Maintenance progress"
- New progress for "Reset Profile"
- Admin in Assistant can see recorded calls
- Diacritical marks support in SMTP server
- Admin in Assistant can see the owners of time conditions
Fixed problems:
- Fix of intercom on OpenStage T40 extender S18
- Fix of doubled extensions in combo boxes
- ACK not recognized by NS on SIP stack



*** Firmware 3.0.1 ***
Improvements:
- FORCE CLIP + new Display CLIP for bundles and ring groups (you can change presentation of caller if the call terminates in ring group or bundle)
- CTI - add HANG UP for SIP extensions
- Busy tone detection

Fixed problems:
- call transfer for SNOM
- SIP - Original caller number not work in transferred
- A Fix for DSP (CPU – Tone detection, DISA, DTMF)
- FIX for Database backup



**** Firmware 3.0.0 ****
New features:
- Call Recording + Assistant management
- Free minutes management
- Free SMS management
- UMTS board support
- SMTP/ SMTPD port (email to sms/ sms to email)
- Queue for user
- Support for Siemens OpenStage / OptiPoint
- Automatic backup DB
- Blinking LED when call to GSM
- Allocation strategy in bundle - By credit, ALL
- Repeat destinations in bundle
- Logout, login to position in bundle
- Cause object in bundle (you can specify causes which will be used for routing to another destination)
- NEW Complex routers + routing on progress info
- CLIR support / Automatic CLIR
- SIP load balancing via SRV[NAPTR]
- BTS info for GSM/UMTS
- MMC card support 512MB < 2GB
- Storage Manager for VoiceMail, Call Recording, Backup of DB
- Call prefix for each number / group to Assistant
- DHCP Server for SIP phones

Improvements:
- When station busy = user busy
- Binary port can be activated during ringing (switch on/off by ring)
- Emergency mode support (if no licence, it will still route emergency numbers to PSTN)
- Exception for Emergency numbers if GSM DID active
- COPY of Profile
- Time conditional to Identification table (different identification during day/night)
- Request-URI add (transport=udp;lr)
New deffault settings:
- Deffault out settings for ICT Enabled is YES
- VoIP Card - Firmware VER. 6.0.1.3 [fix FAX issue, DTMF detector issue]
- G729 ANEX B = NO (possibility to disable/deny ANEX B)
Fixed problems:
- ISDN BRI fixed problem (BRI + DSL modem)
- Fix: SIP terminals hold after entry into service or conference room
- Fix: FSK CLIP problem